iPhone 7 Plus housing replacement in Almaty

Aluminium Body, Antenna Lines and Water Resistance

This model uses a single aluminium back with the antenna bands moved to the top and bottom edges, and it was the first Plus model rated for water resistance. The mid-frame is stiffer than the 6s, so the body resists bending better, but the antenna inserts sit in the panel itself and must rest flush after any swap. Splash protection comes from a glue gasket running around the inside of the frame, not from a rubber ring, so the contour has to be re-laid cleanly to keep dust and moisture out. Once the chassis is opened, the factory seal is broken — a fresh gasket restores splash protection but not the original rating, so treat the device as water-resistant, not waterproof, afterwards.

How the 7 Plus Compares to the 6s and the 8 Plus

Back Glass or Full iPhone 7 Plus Housing Replacement

The 7 Plus has an aluminium rear panel, so swapping just the glass as on an 8 Plus does not apply. The real choice is a full housing replacement or a local fix of the chassis geometry.

When a Full Housing Is the Only Option

A full iPhone 7 Plus housing replacement is the right call when the chassis is dented, twisted or the antenna lines are cracked, because a new panel cannot sit flush on a bent body. We see this most on phones that took a corner hit: the aluminium around the camera cutout folds inward, the mid-frame bows by a millimetre or two, and the gap under the antenna insert opens wide enough to catch a fingernail. Local straightening can pull a shallow dent back, but it never restores the original tolerance across the whole plate. A corner dent often hides a twisted mid-frame — we check flatness on a surface plate before quoting. If you are looking for iPhone 7 Plus housing replacement in Almaty, we can assess the chassis and confirm whether a full housing is needed.

What to Do Before You Bring the Phone In

• Tape the edges: a strip of clear tape stops glass splinters from cutting your fingers.
• Skip tight pockets: pressure on a cracked rear widens the seam and lets dust in.
• Pause wireless charging: if the cover is lifting, the coil overheats against the gap.
• Keep it dry: moisture through an open seam reaches the board before you notice.
• Book a slot: a photo on WhatsApp gets you a quote and a free time window.

How We Rebuild Your Phone With iPhone 7 Plus Housing Replacement

A housing swap is not a cosmetic cover-up: every internal component moves into a fresh housing. Here is what travels across, how we lock the terms down, and what you leave with.

What Moves From the Old Housing to the New One

We move the logic board, battery, both rear cameras, Taptic Engine, speakers, charging flex and button flexes into the new frame, then re-fit the display and re-glue the seal. Each flex is released from its adhesive strip rather than pulled, and the antenna contacts are transferred with their original springs so signal behaviour stays as it was. The dual camera of the 7 Plus is the fiddly part — its bracket is matched to the housing opening, so a housing with slightly off holes shows up as a misaligned lens ring, which is why we dry-fit before final assembly. Our engineers have handled this rebuild for 11 years and run 46,000+ repairs, so the order of transfer is routine rather than improvised.

Photo, Receipt, Part in Packaging, Handover

• Send a photo: the engineer quotes from the picture within 5 minutes on WhatsApp.
• Free diagnostics: 15 minutes in front of you, even if you decide not to repair.
• Receipt first: price, part, turnaround and warranty are written down in 2 minutes.
• Part shown: the new housing is opened from factory packaging before installation.
• Wait or drop off: 72% of repairs finish while the customer waits in the lounge.
• Handover: you leave with the receipt, warranty card and the old housing.

What We Check After the Rebuild

Once the phone is back together, it undergoes a 32-function verification that takes about 10 minutes. You complete it alongside the engineer, so every result is visible on the spot instead of taken on trust.

The 32-Point Check We Run Together

After the rebuild we run a 32-function check of about 10 minutes, covering Touch ID, both cameras, microphones, speakers, charging, network and the buttons, and you complete it alongside the engineer. The same pass confirms the vibration motor, both SIM slots and the proximity sensor that blanks the screen during calls. We test the front and rear camera separately, play audio via the earpiece and the loudspeaker, and confirm the Lightning port charges and syncs. The engineer notes any function behaving outside spec before you leave the waiting area. Touch ID on the 7 Plus is tied to the original home button, so a housing swap keeps your button — if fingerprint unlock ever fails after a repair elsewhere, the button was replaced, not the housing.

Camera Glass and the Lens Ring

If the camera glass on your 7 Plus is cracked but the frame is straight, we replace just the protective glass; when the island itself is deformed, it is swapped together with the housing. The dual camera module sits under that glass, so we cover the optics with protective film before any heat or prying near the opening. A fresh ring is seated flush with the new housing, and we check that the opening stays centred over the module once the housing is closed. A scratched surround scatters light in low-light shots long before it looks broken, so we inspect it under magnification during the same visit rather than waiting for blurry photos.

Original or Aftermarket Housing and What It Changes

On the 7 Plus an original and an aftermarket housing differ in the aluminium tone, how the inserts sit and how precisely the holes line up. The choice is fixed on the receipt before work starts.

Fit, Shade and Antenna Inserts

Can You Change the Colour of a 7 Plus

Yes — since the whole housing is replaced, you can move a 7 Plus into a different factory colour, such as swapping a worn matte black body for a jet black or gold one. The frame, the back panel and the antenna lines arrive as a matched set, so the phone reads as a single colour rather than a patched-up unit. Wear is the other reason people ask: scuffed corners and polished edges disappear with the old panel, and the device looks new again without touching the screen or the board. The 7 and 7 Plus both gained water resistance, and a fresh housing restores the sealing surfaces the old one lost. A colour change is only skin-deep, though — the SIM tray and the button caps should match the new housing, otherwise the mismatch is the first thing a buyer notices.