iPhone 7 Plus Housing Replacement in Astana

Why the 7 Plus body dents and bends

The 7 Plus chassis is a single piece of thin aluminium, so a drop that would crack the panel on newer models leaves a dent or a slight bend along the edges instead. The metal is soft enough to take the impact, and the antenna inserts at the top and bottom ends create two zones where the chassis flexes more than elsewhere. A bent body is not cosmetic — it presses on the display assembly and the battery, so a phone that still works can slowly develop screen lift or swelling. If the shell has shifted, an iPhone 7 Plus housing replacement in Astana restores the shape and the fit of the panels. Check the device on a flat table before deciding the repair is only about looks: if it rocks, the middle section has already shifted out of line.

What to do before you bring the phone in

• Cover sharp edges: a strip of tape over a dented or cracked area keeps splinters away from your fingers.
• Keep it dry: a bent shell no longer seals properly, so avoid rain, sinks and steamy rooms.
• Skip wireless charging: on a damaged back the coil can sit unevenly and overheat.
• Do not force the SIM tray: a warped housing pinches the tray and the side buttons.
• Bring it in early: a small dent is easier to correct than a body that has already pressed on the display.

Back panel or full housing, which the 7 Plus needs

The 7 Plus has no separate rear glass, so the choice is between replacing the damaged panel and rebuilding the phone into a new housing. The condition of the frame and the camera island decides which route fits.

When a new housing is the only option

We recommend a full housing replacement when the chassis is bent, deeply dented or the antenna lines and corners are deformed, because a new back panel will not sit flush on a warped body. The middle frame carries the display seating, the button cutouts and the antenna inserts in one piece, so any twist in that aluminium shows up as uneven gaps around the screen and a home button that no longer travels cleanly. A cover-only swap on such a body leaves the damage underneath, and the fresh part picks up the same curve within weeks. A body that is off by even a fraction of a millimetre changes how the display sits and how the buttons travel, so the decision is made on geometry, not on how visible the damage is.

Comparing the repair options for a 7 Plus

How we carry out an iPhone 7 Plus housing replacement in Astana

A housing swap on the 7 Plus is a full rebuild: the board, battery, dual camera and button flexes all move into a fresh shell, and the device is then assembled and checked.

From WhatsApp photo to a finished housing replacement

A housing replacement starts with a photo on WhatsApp, where an engineer replies within five minutes, quotes a price and offers a free time slot. The part type, turnaround and warranty are written on the receipt before any screw is out, so nothing about the job shifts halfway through. Most of these rebuilds finish in 20–40 minutes while you sit in the waiting area with coffee and Wi-Fi — 72% of our jobs never leave the bench overnight. A courier can be called if you would rather not travel across the city. That document deserves a close read: it locks the cost, the part and the guarantee before work begins, and it protects you if a question appears months later.

What happens to the parts inside the old frame

• Teardown: the display comes off first, then the board, battery and camera module are freed from the old shell.
• Transfer: every internal piece is moved into the replacement body and seated on fresh adhesive.
• Reseal: a water-resistant gasket goes around the perimeter, though it never matches the factory seal.
• Reassembly: the screen goes back on and the handset is powered up for the first check.
• Handover: you leave with the phone, the receipt, the warranty card and the old housing.

What we check on a 7 Plus after the new housing is on

Once the new shell is back on, the job is not finished until the phone behaves like a whole device again. We go through everything that depends on the housing before you take it home.

The 32-point check we run with you

After the housing is on, we run a 32-function check that takes about ten minutes and go through the results with you before you leave. The list covers the dual camera, both volume keys and the mute switch, the home button, charging, cellular network, Wi-Fi, microphones and both speakers, and you watch each result on the screen. The dual camera is the item to test hardest on a 7 Plus — a housing that sits slightly off can shift the second lens out of alignment, and that shows up as blurry portrait shots rather than an obvious fault. We photograph a test portrait and a zoomed shot and compare them side by side, because the second lens is the first thing a misaligned body spoils.

What water resistance to expect after the swap

A 7 Plus that has had its housing replaced is no longer water-resistant as it left the production line, even with a fresh gasket, because the seal is only as good as the adhesive and the fit of the replacement shell. The original gasket is compressed once during assembly and cannot be reused at the same pressure, so the fresh bead of sealant is what stands between the board and moisture. Treat the phone as splash-resistant at best — a dropped-in-the-sink moment that the initial seal would have survived is now a real risk. Keep it out of the bathroom during hot showers and away from rain, and dry the charging port with a cloth rather than a heater if it does get wet. Before you hand the phone in, make a backup so your photos and messages are safe whatever the outcome.

Original or aftermarket housing and how the 7 Plus looks afterwards

A 7 Plus body comes in a genuine version and a copy, and the difference shows in shade, gap fit and how the buttons seat. We fix your choice on the receipt before any work starts.

How original and aftermarket housings differ

A genuine housing matches the factory colour and gap tolerances, while a copy can differ slightly in shade and how the buttons and SIM tray sit. We show the new part in its factory packaging before installation, so you see the finish and the antenna inserts with your own eyes rather than trusting a photo. Our engineers handle both types daily, and 64% of customers pick the genuine part — mostly because the fit around the mute switch and the camera cutout is tighter on it. The cheaper option often looks close at arm's length, though the anodised layer tends to wear faster on the corners. On a 7 Plus the antenna lines are the giveaway — copies often show a slightly different line colour, so look at the top and bottom edges before you approve the part.

Can you change the colour of a 7 Plus

Yes, a 7 Plus can come back in a different colour if the housing you choose is available in that shade, since the whole shell is replaced rather than repainted. The body is one solid aluminium piece, so the finish you get is the finish of the part, not a coat over the old scratches. Rose gold, silver, black and jet black versions all turn up in stock, and the swap keeps the original glass and display if they survived the drop. A repainted surface is a different story — paint fills the antenna gaps and flakes off within months, which is why we do not offer it. A colour change is a cosmetic decision, not a value one — on a phone this age the resale gap between shades is small, so pick the tone you actually want to carry.