iPhone 6s Plus Glass Replacement in Astana

How to tell the LCD and touch layer are still fine

We check the 6s Plus in front of you for a clean image with no dark spots, lines or bleeding, and for input that responds across the whole display, including the edges. The engineer runs a free diagnostics for 15 minutes and shows you the panel live: a hairline split, a corner chip or a spiderweb pattern on the outer glass alone leaves the LCD intact when the picture stays even and every swipe registers. What matters is the layer beneath the surface — the liquid-crystal matrix and the digitizer grid — not the depth of the line you can feel with a fingernail. A break that runs above the selfie camera or the earpiece is worth flagging early, because dust and moisture reach the LCD through it faster than through a small nick at the edge.

When only a full display module will fix it

If the image shows dark patches, coloured lines or a dead input zone, replacing the glass alone will not bring the screen back, and we tell you this before any work begins. Those symptoms mean the liquid-crystal matrix or the digitizer underneath is already damaged, and bonding new glass over it would only seal a faulty panel. A bent frame or a lifted module tells the same story: the display has taken the impact, not just its surface. A 6s Plus that took a hard hit can look fine at first and develop pressure marks a day later, so the honest moment to decide between glass and a module is the check, not the first fracture.

How iPhone 6s Plus glass replacement works step by step

We take the phone from the module lift to final assembly in clear stages. The 6s Plus carries an LCD with a 3D Touch layer, so separating the glass runs more carefully than on an OLED screen.

Separating the broken glass and bonding the new one

The technician lifts the display module, heats and separates the shattered glass from the screen, clears the old adhesive, then bonds a new pane onto optical OCA glue and laminates it to push out air. OCA is a clear optical adhesive sheet that holds the new glass to the display and lets light pass through without haze. Lamination runs in a vacuum press, where pressure and heat cure the glue evenly across the whole surface. The 3D Touch layer sits directly under the glass on this model, so the separation temperature and pressure matter more than on a plain LCD, which is why the job is done in-house rather than outsourced. This is how iPhone 6s Plus glass replacement in Astana goes at our workshop, from separation to the finished pane.

What the process looks like from your side

You send a photo of the damage on WhatsApp, an engineer replies within 5 minutes with a price and a free slot, and most of the job is finished while you wait in the seating area with coffee and Wi-Fi. Turnaround for this task is 40 minutes, and 72% of repairs at our workshop are completed while the customer waits. A courier can be called if you would rather not come in, and payment works by Kaspi, card or cash. Because the price, the part and the turnaround are written on the receipt before work starts, there is no surprise line added after the glass is already off.

What stays original after iPhone 6s Plus glass replacement

Bonding fresh glass keeps the phone's own display panel and everything wired to it. Here is what does not change during the procedure and why that matters for a 6s Plus.

The original LCD, 3D Touch and Touch ID stay in place

Only the front pane is replaced, so the original LCD, the pressure layer and the Home button with the fingerprint sensor remain the parts that came with your phone. Our technicians separate the shattered pane from the panel, clean the old adhesive and bond a fresh pane on optically clear adhesive, leaving the matrix and the pressure sensors untouched. The Home button is never swapped, so its paired fingerprint chip keeps talking to the same logic board. 64% of customers choose an original part, and on a glass-only job that panel is the one already inside the device. Keeping it also preserves the factory colour and brightness calibration, which a swapped module rarely matches exactly on a 6s Plus.

Glass versus a full module at a glance

How we check the result before you take the phone home

Acceptance happens together with the engineer, not on your own at the counter. We show you what to look at so a lamination defect does not appear a week after pickup.

Touch, bubbles and backlight you can check yourself

After the repair you run your finger along every edge of the 6s Plus, tilt the screen to look for trapped dust or air under the glass, and check the backlight is even on a white background. Sweep the perimeter slowly: the corners and the strip above the home button are where a lifted lamination shows first, and a quick swipe across the middle tells you nothing. Tilt the phone under a lamp at a shallow angle — dust specks sit still, air pockets shift as the glass moves. For the backlight, open a blank white note at full brightness in a dim corner of the room. A faint halo right at the border is normal for the first hours as the adhesive settles, but a sharp bubble that stays put is a reason to speak up before you leave.

The functions we test together with you

We go through 32 functions with you in about 10 minutes, including 3D Touch, the fingerprint sensor, the front camera, both microphones, the speaker, charging and the network. The fingerprint sensor is re-scanned with your own finger, not ours, because it reads the ridge pattern it was paired with. The front camera gets a live preview, both microphones record a short voice note played back on the speaker, and the charger is plugged in with the cable you brought. The pressure layer is worth pressing at different strengths on the 6s Plus specifically, because a poorly bonded panel can register a light tap but miss a firm press.

Warranty, paperwork and the part you get back

A repair is only as good as the terms attached to it. Here is what gets written down before the technician opens the device, and what travels home with you afterwards.

The receipt, the warranty card and the old glass

Before work starts we write the part, the turnaround and a warranty of up to 1 year on the receipt, and when you collect the device you get the receipt, the warranty card and the old glass back. Fixing those points on paper takes about 2 minutes and happens before the module is touched, so nothing about the job is decided mid-repair. The removed glass is bagged and labelled with your device, not thrown away with the shop waste. Keeping it is useful if you ever need to prove what was originally fitted, whether for a resale conversation or a dispute over condition. On a 6s Plus the detached front panel also shows the technician's separation line, which tells you how much of the original assembly stayed in place. Ask for the bag at pickup if it is not already in the box.

Choosing the part and paying the way you prefer

You choose between an original part and an aftermarket one, we show the new glass in its factory packaging before installation, and you can pay by Kaspi, card or cash. The packaging is opened in front of you rather than in the back room, so the seal and the part number are visible at the moment the cracked layer comes off. Most of our customers, 64%, pick the original part, and on a 6s Plus the decision usually comes down to how closely the new glass matches the factory touch feel and the colour tint under daylight. Aftermarket glass is the cheaper route and works fine for a handset kept as a spare. Payment is settled once you have inspected the result, not upfront.